Journal Articles
Permanent URI for this collectionhttps://mro.massey.ac.nz/handle/10179/7915
Browse
3 results
Search Results
Item AI-Based Controls for Thermal Comfort in Adaptable Buildings: A Review(MDPI AG, 2024-11-04) Ahsan M; Shahzad W; Arif KDue to global weather changes and pandemics, people are more likely to spend most of their time in indoor environments. In this regard, indoor environment quality is a very important aspect of occupant well-being, which is often ignored in modern building designs. Based on our research, thermal comfort is one of the essential items in building environments that can improve the mental stability and productivity of the occupants if the building’s indoor environment is created in a way that meets the occupants’ comfort requirements. Buildings nowadays operate on adaptive or stationary models to attain thermal comfort, which is based on Fanger’s model of the Predicted Mean Vote (PMV). Based on the literature review, limited work has been carried out to enhance the quality of the inside environment, and most research work has been devoted to building energy management. Moreover, there have been no definite solutions so far that have the capability to detect the thermal comfort requirements of multiple occupants in real time. Modern buildings tend to operate on predefined set point parameters to control the indoor environment based on the measured room temperature, which can be different from the thermal comfort requirements of the occupants. This paper discusses the limitations and assumptions that are associated with the existing thermal comfort solutions and emphasises the importance of having a real-time solution to address the thermal requirements of occupants.Item Low-Cost CO Sensor Calibration Using One Dimensional Convolutional Neural Network(MDPI AG, 11/01/2023) Ali S; Alam F; Arif K; Potgieter J-GThe advent of cost-effective sensors and the rise of the Internet of Things (IoT) presents the opportunity to monitor urban pollution at a high spatio-temporal resolution. However, these sensors suffer from poor accuracy that can be improved through calibration. In this paper, we propose to use One Dimensional Convolutional Neural Network (1DCNN) based calibration for low-cost carbon monoxide sensors and benchmark its performance against several Machine Learning (ML) based calibration techniques. We make use of three large data sets collected by research groups around the world from field-deployed low-cost sensors co-located with accurate reference sensors. Our investigation shows that 1DCNN performs consistently across all datasets. Gradient boosting regression, another ML technique that has not been widely explored for gas sensor calibration, also performs reasonably well. For all datasets, the introduction of temperature and relative humidity data improves the calibration accuracy. Cross-sensitivity to other pollutants can be exploited to improve the accuracy further. This suggests that low-cost sensors should be deployed as a suite or an array to measure covariate factors.Item A Performance-Optimized Deep Learning-based Plant Disease Detection Approach for Horticultural Crops of New Zealand(Institute of Electrical and Electronics Engineers, 23/08/2022) Saleem MH; Potgieter J; Arif KDeep learning-based plant disease detection has gained significant attention from the scientific community. However, various aspects of real horticultural conditions have not yet been explored. For example, the disease should be considered not only on leaves, but also on other parts of plants, including stems, canes, and fruits. Furthermore, the detection of multiple diseases in a single plant organ at a time has not been performed. Similarly, plant disease has not been identified in various crops in the complex horticultural environment with the same optimized/modified model. To address these research gaps, this research presents a dataset named NZDLPlantDisease-v1, consisting of diseases in five of the most important horticultural crops in New Zealand: kiwifruit, apple, pear, avocado, and grapevine. An optimized version of the best obtained deep learning (DL) model named region-based fully convolutional network (RFCN) has been proposed to detect plant disease using the newly generated dataset. After finding the most suitable DL model, the data augmentation techniques were successively evaluated. Subsequently, the effects of image resizers with interpolators, weight initializers, batch normalization, and DL optimizers were studied. Finally, performance was enhanced by empirical observation of position-sensitive score maps and anchor box specifications. Furthermore, the robustness/practicality of the proposed approach was demonstrated using a stratified k-fold cross-validation technique and testing on an external dataset. The final mean average precision of the RFCN model was found to be 93.80%, which was 19.33% better than the default settings. Therefore, this research could be a benchmark step for any follow-up research on automatic control of disease in several plant species.
